#
|
PART #
|
DESCRIPTION
|
RETAIL $U.S.
|
|
WAC
|
Complete carpet wand for M2, TC2 and SC2
|
$35.00
|
|
WACS
|
Complete upholstery tool for M2, TC2 and
SC2
|
$18.75
|
|
M1WAND
|
Complete carpet wand for M1, TC1 and SC1
|
$21.25
|
|
CAP/DIP
|
Complete jug cap and dip tube including
strainer
|
$24.59
|
|
|
To upgrade to jug qc
system: buy #F17004LG & M22004LG, cut suction tube 13 inches
up from strainer, push #F17004LG into tube hanging in sprayer,
push
tube with strainer onto the barb under #M22004LG.
|
|
1A
|
TPU8004SS
|
Stainless Steel TJET carpet tip (brass tip
#TPU8004 is $4.75)
|
$11.67
|
1B
|
TPU50015
|
Brass TJET upholstery tip
|
$4.75
|
2
|
CP1325
|
Brass hex nut
|
$2.50
|
2A
|
CP1335
|
Brass body holding
strainer (for carpet wand) (1/8 female)
|
$2.50
|
2A'
|
CP1336
|
Brass body holding
strainer (for upholstery wand) (1/8 male)
|
$2.50
|
3&3A
|
SS20
|
Stainless steel tube
threaded
|
$16.67
|
4
|
H1/8DT-SS8004
|
Female SS V-JET tip,
8004(#H1/8DT-8004 - brass is $4.17)
|
$12.00
|
4A
|
AB110CA
|
Brass connector 1/8"
female/1/4" male to trigger
|
$2.50
|
| 5 |
BST-1YSS |
Female S. Steel
QC(viton)(brass is $7.84)
male is BST-N1SS (see below)
|
$12.50 |
| 6 |
6590 |
Br/SS Trig/valve |
$44.00 |
| * |
6590VIKIT |
Trig/Valve Rep. Kit |
$19.17 |
| 7 |
125HBL-4-4 |
Br. Hose Barb 1/4, 1/4 |
$1.50 |
| 8 |
FW-10 |
Coil Spray Hose 1/4"
I.D.(or)
|
$27.50 |
| 8 |
801-4-10 |
Straight Spray Hose
1/4" I.D.
|
$27.50 |
| 9 |
SNP-2 |
Nylon Hose Clamp |
$0.92 |
10
|
SPGD
|
Spring Guard for spray hose
|
$2.84
|
| 11 |
N4MEB6 |
Nylon Elbow, 3/8 NPT |
$2.09 |
| 12 |
AQ115
|
115 V, Motor/Pump, 70
psi
|
$128.34 |
13
|
2G
|
2 Gallon Solution
Container/w 43 mm opening
|
$5.75
|
| 14 |
216P-4-2 |
Brass Reduce Nipple |
$1.67 |
| 15 |
11375 |
Rubber Hose Grommet |
$1.67 |
| 16 |
ARD* |
Nylon Base Plate Ret.
Pin(4) |
$0.67 |
| 17 |
160011E |
ON/OFF Switch |
$4.59 |
| 18 |
UR33
|
Urethane Hose, 33",
1/4"I.D., Pump to #19. Old # was 801-4-46
|
$5.00 |
| * |
9600K35 |
Cap/Grommet(slides on
suction hose)Old Design
|
$2.17 |
| 19 |
F17004LG |
Female QC with check
valve, will not drip
|
$10.00 |
| 20 |
M22004LG |
Male QC with check
valve (includes cap & panel mount, not dip tube)
(Male QC only, without cap and panel mount, is $10.00)
|
$16.67 |
| 22 |
UR12.5 |
12.5", 1/4" I.D.
urethane
tube
|
$2.00 |
| 23 |
13862-50 |
Suction Hose Strainer
|
$6.09 |
| 24 |
4193A-10-50SS |
Strainer check valve
inside brass body (#2A-#CP1336)
|
$5.59 |
| 25
|
BST-N1SS |
Male QC, stainless
steel. (brass is $2.42 list)
|
$5.55 |
| 26 |
SR7W2 |
Cord
Restrainer
|
$2.50 |
| 27
|
18110 |
Power cord 20'
|
$20.00 |
|
DKIT2
|
2 Part pump kit for
D3621V1311 pump (Flojet)
|
$62.00
|
Flojet Pump Parts
|
21010-001
is diaphragm(round) - $38.75, 20914-002A is check valve(rectang.) -
$23.25 - 21004-101 is diaphragm/CAM kit $48.09.
|
Aquatec Pump Parts
|
(for 12
and 115 volt)#UHA - $23.34 Black poly pump head. #VHA - $23.34 Valve
assembly. #LHA - $31.67 Diaphragm/CAM
|
If Aquatec pump runs but does not spray, replace #VHA &
#LHA. If Aquatec pump leaks from small triangle on black
pump head (#UHA), replace #UHA. Always spray fresh water after
use of diluted solvents and at the end of the day.
|
WAND PARTS ... (wands made before 2003
had compression fittings, new wands are threaded)
|
| |
M1 wand
parts: #8004WAND = $21.25
|
| |
H1/8DT-8004SS-$7.20(Br.
is $4.17)
is female V-Jet Tip, SS20-$16.67 is threaded 20 inch SS tube,
AB110CA-$2.50 is 1/8/1/4 brass connector
|
| |
M2 wand
parts: #WAC =
$35.00 #WACS = $18.75
|
WAC
(carpet wand) |
BST-N1SS-$5.55
(male QC-brass available #BST-N1-$2.42), threaded 20 inch SS
tube-$16.67,
CP1335-$2.50(brass body),
4193-A-10-50SS-$5.84(50 mesh strainer with 10 lb. check valve),
TPU8004SS-$11.67(SS
T-Jet tip)(BR. is $4.75), CP1325-$2.50(Brass hex nut).
|
WACS
(uphols. tool)
|
BST-N1-$2.42(Brass
male QC), CP1336-$2.50(brass male body), 4193-A-20-50-$5.84(50 mesh
strainer with
20 lb. check valve), TPU50015-$4.75(BrassT-Jet tip), CP1325-$2.50(brass
hex nut)
|
|
230 volt Flojet pump is part # D3732V1311 $ 159.17
|
800-669-2469 
